By Walnut Creek Water Damage editorial team ·
Keep a working copy
On this page
Provider and leak tests
What should you confirm before starting the meter test?
Confirm that the address is served by EBMUD for water before using its meter instructions. EBMUD publishes a service-area map and distinguishes water service from wastewater service. A postal city name is not proof of the water provider. If the property is in a multi-unit building, ask the property manager or Mutual who controls the meter and the interior valves before opening anything.
Locate the meter without entering unsafe water, moving traffic or a confined space. Do not lift a heavy or damaged meter cover, reach into a flooded meter box or touch electrical equipment near standing water. If the box is unsafe, obstructed or unfamiliar, stop and contact EBMUD. A meter test is not worth an injury, and this guide does not authorize utility work.
Know which valve you may safely operate. Many homes have a house shutoff and a separate irrigation shutoff, but layouts vary. Do not force a stuck valve or dismantle a fitting. If a valve will not turn by hand or its condition is uncertain, stop and ask a plumber or the property manager. Write down the valve locations and who authorized any operation.
Scroll sideways to see all three columns.
| Check | Why it matters | Safe alternative |
|---|---|---|
| Water provider | EBMUD instructions apply only where EBMUD provides water service. | Check the EBMUD service map or call the utility before using the meter procedure. |
| Meter access | A flooded, damaged or traffic-adjacent meter box can be hazardous. | Stop and contact EBMUD; do not open or reach into an unsafe box. |
| Valve condition | Forcing a stuck valve can cause a new leak or injury. | Leave it alone and ask a plumber or property manager. |
| Building responsibility | A condo or Mutual may control shared valves and meter areas. | Ask the manager or Mutual before operating shared equipment. |
This is a safety and service-boundary check, not a determination of who owns or repairs the meter, valve or line.
What is the 30-minute meter test?
Turn off all known water use indoors and outdoors. Check that no one will shower, flush, run a tap, start the dishwasher, run the washing machine, use an ice maker or start an irrigation cycle during the test. If a water softener, recirculation pump or other automatic device uses water, note it and ask the appropriate professional whether it affects the test. A moving meter during an automatic cycle can look like a leak.
Record the meter reading and photograph the display if that is safe and permitted. Note the leak-indicator position. Wait 30 minutes without any water use. Then recheck the reading and indicator. Movement suggests a leak. No movement does not rule out a small, intermittent or recently stopped leak. This is a 30-minute meter observation, not a 10-minute test. A quick visual check may be shorter, but the complete test should not be described as ten minutes.
If the meter moves, do not immediately conclude that a particular fixture is leaking. The movement tells you water is passing the meter; it does not identify the location. Use the valve and fixture checks below to narrow the question. If the meter does not move, retain the reading and note the test conditions. A high bill with no movement may involve an intermittent event, irrigation, occupancy changes or another cause.
Scroll sideways to see all three columns.
| Step | What to do | What the result can mean |
|---|---|---|
| 1. Stop water use | Turn off indoor and outdoor fixtures; note automatic water-using devices. | A device left running can create false movement. |
| 2. Record the start | Note the reading, indicator position and time; photograph if safe. | Creates a comparison point without opening or repairing anything. |
| 3. Wait 30 minutes | Keep all water use off for the full interval. | A shorter glance is not the complete test. |
| 4. Recheck | Compare the reading and indicator; record the end time. | Movement suggests a leak; no movement does not exclude every leak. |
The meter test identifies possible water passage, not the leak location, repair responsibility or repair cost.
How do you distinguish a houseline leak from irrigation?
EBMUD describes a houseline check using the house valve and any applicable separate irrigation valve. With the valves in the instructed positions, mark or photograph the meter position and wait another 30 minutes. Compare the result. The purpose is to isolate a branch, not to prove that every pipe on that branch is sound. Valve layouts vary, and a label may be wrong or missing.
If the house valve is closed and the meter still moves, the movement may involve an irrigation branch, a service line or another path. If movement stops when the house valve is closed and resumes when it is opened, the observation points toward the house-side plumbing. Those are investigative clues, not a repair diagnosis. A hidden leak, a failed valve seat or a cross-connection can complicate the result.
Do not close a valve that controls fire protection, a shared building supply or an unfamiliar system without authorization. In a condo or Mutual property, a shared valve may affect neighbors. Ask before operating it. Record the valve position, who authorized it, the start and end times, and the meter readings. If you cannot identify the valve safely, stop and call a plumber or the property manager.
Scroll sideways to see all three columns.
| Test condition | Observation to record | What it may suggest |
|---|---|---|
| All water use off | Meter reading and indicator at start and after 30 minutes. | Movement suggests water is passing the meter. |
| House valve closed | Valve position, meter reading, start and end time. | Continued movement may point to a branch outside the house valve. |
| House valve reopened | Whether movement resumes and how quickly. | A clue toward house-side plumbing, not a final diagnosis. |
| Irrigation valve closed | Whether the branch is separate and what changes. | Helps isolate an irrigation path when the layout is known. |
Do not force valves or operate shared/fire-protection valves without authorization. Valve labels and layouts can be wrong.
What does the toilet dye test involve?
EBMUD describes a toilet dye test with a 15–30 minute wait. Place dye in the tank according to the product instructions, without flushing, and wait. If color appears in the bowl without a flush, the flapper or another tank-to-bowl path may be leaking. Record the toilet location, the dye product, the start time and what you observed. A faint color can be easy to miss, so use the product's instructions and a consistent light source.
Do not use a dye method that conflicts with the fixture manufacturer's instructions or a water-treatment system. Do not dismantle the tank if you are not comfortable doing so. A toilet leak can waste water continuously while looking like a minor issue. If the toilet is running, refilling repeatedly or showing color in the bowl, ask a plumber or the property manager to inspect it.
The dye test is only one branch of the investigation. A negative dye test does not clear the supply line, irrigation, water heater, washing machine, dishwasher or hidden plumbing. It also does not prove who is responsible for the repair in a condo or rental. Keep the result with the meter readings and the other observations.
Bills and responsibility boundaries
How should you read a high bill without assuming one cause?
A high bill is a reason to investigate, not proof of a hidden leak. Compare the billing period with the previous period and the same period last year. Note changes in occupancy, irrigation, guests, laundry, pool or spa use, water softener regeneration and outdoor watering. A bill can reflect a rate change or a meter-reading issue as well as water use. Do not tell a resident that a high bill proves a leak.
Look for continuous movement at the meter when no water should be running. An intermittent leak may not be active during the test. A toilet can cycle on and off. An irrigation valve may run on a schedule you did not notice. A pressure-reducing valve or an appliance can produce intermittent flow. Record the conditions so a plumber or EBMUD representative can interpret the result.
Do not promise a specific savings amount from a repair. The bill impact depends on the leak rate, the billing period, rates, credits and other use. This guide does not calculate a leak volume or a payback. If the bill is unexpectedly high, ask EBMUD about the reading and the account, and ask a qualified plumber to investigate the customer-side plumbing.
What are EBMUD responsibilities and customer responsibilities?
EBMUD's published leak guidance describes the utility as handling street-side leaks including the meter and connection threads. Customers handle customer-side leaks and repairs. That boundary is useful for deciding whom to call, but it does not resolve every property question. A condo or Mutual may have its own allocation between the member and the association. A landlord and tenant may have a separate agreement. A property manager may control access to a shared meter room.
If the suspected leak is at the meter or on the street side, contact EBMUD and describe what you observed. Do not attempt to repair utility-side equipment. If the leak is on the customer side, ask a licensed plumber or the responsible property professional. If water has entered building materials, a restoration assessment may be needed after the source is controlled. Those are separate service questions.
Do not imply that EBMUD endorses this website or that this guide can authorize a repair, a rebate or a billing adjustment. EBMUD's current instructions and account-specific answers control. Record the utility contact, date, reference number and any instruction you receive. Keep that record with the meter worksheet.
Rebate and next steps
What are the current Flowmeter Rebate terms?
The EBMUD Flowmeter Rebate page retrieved for this research describes a rebate of 50% of eligible device cost, up to $200. The amount excludes tax, shipping and installation. It is limited to one device per service address. The program requires installation at an active EBMUD service, a qualifying device, an application within 90 days of purchase, a dated receipt and an installed-device photo, and at least two years of operation. Device eligibility must be checked before purchase.
This is more precise than saying “EBMUD pays $200 for a leak fix.” The rebate is a percentage with a ceiling, not a blanket cash payment, and it applies to an eligible flowmeter device under the program terms. It is not a rebate for every repair, a restoration discount or a guarantee that a particular device qualifies. Confirm the current terms, device list and application process on the EBMUD page before buying or installing anything.
Keep the purchase receipt, device model, installation date, photo and application record. Ask EBMUD whether the proposed installation meets the program requirements. Do not represent this website as an EBMUD rebate agent or as an approved contractor. If the property is a condo or Mutual, ask who owns the device and who can apply before installation.
Scroll sideways to see all three columns.
| Term | What the retrieved page states | What to confirm |
|---|---|---|
| Rebate amount | 50% of eligible device cost, up to $200; excludes tax, shipping and installation. | Current program page, eligible cost definition and any changed ceiling. |
| Device limit | One device per service address. | Address eligibility and whether the property has an existing device. |
| Service requirement | Installation at an active EBMUD service. | Account status and address-level water service. |
| Application timing | Apply within 90 days of purchase with a dated receipt and installed-device photo. | Current application instructions and required documents. |
| Operating term | At least two years of operation. | Current agreement terms and any owner or Mutual approval. |
Retrieved EBMUD terms can change. This is not a rebate approval, a device endorsement or a promise of payment.
What should you record and when should you call a professional?
Use the printable EBMUD leak-check worksheet to record the address, water provider, meter location, start and end times, readings, indicator position, valve tests, toilet dye result and any automatic water use. Add the date and the name of the person who performed each step. If a step was not safe or not completed, write that instead of leaving a misleading blank.
Call EBMUD for a suspected meter or street-side leak and for account or meter-access questions. Call a plumber or property professional for a customer-side fixture, supply line, valve or appliance leak. Consider a restoration assessment if water has soaked drywall, flooring, cabinets or other building materials. Do not wait for a meter test to address an active leak that is causing damage; stop the water only if it is safe to do so.
Keep the worksheet with the bill, photographs and correspondence. If a repair is performed, add the invoice, scope and date. The record helps compare a future bill and shows what was already checked. It does not replace the utility's records or a plumber's diagnosis.
What cannot be decided from this web guide?
A meter record cannot locate a hidden leak, diagnose a defective fixture or line, set a repair price, approve a rebate or decide who pays in a condo, rental or Mutual. Confirm address-level water and wastewater service directly with the utility.
Use the official EBMUD pages and your property documents for those questions. If the meter box, valves or electrical conditions are unsafe, stop. If the leak is active and causing damage, contact the appropriate emergency or property professional. A web worksheet is a record-keeping aid, not a repair authorization or a coverage decision.
Common questions
Is the EBMUD leak test only 10 minutes?
No. The meter observation described here uses 30 minutes without water use. An initial visual check can be quicker, but the complete test should not be called a 10-minute test.
Does a meter that stops moving mean there is no leak?
No. A small, intermittent or recently stopped leak may not move the meter during the test. Record the conditions and investigate fixtures, valves and the bill history.
Can I open the meter box myself?
Only if it is safe and permitted. Do not lift a heavy or damaged cover, reach into a flooded box or touch electrical equipment. Contact EBMUD if access is unsafe or uncertain.
Does the Flowmeter Rebate pay a flat $200?
The retrieved terms describe 50% of eligible device cost, up to $200, excluding tax, shipping and installation. Confirm current terms and device eligibility before purchase.
Will EBMUD repair a leak inside my home?
EBMUD describes street-side responsibility including the meter and connection threads; customers handle customer-side leaks and repairs. Ask EBMUD about the specific location.
Sources and scope
Organizational leak-check guide prepared by Walnut Creek Water Damage using EBMUD published leak and high-bill guidance. EBMUD is not affiliated with or endorsing this business. Valve layouts and address-level service vary; do not force stuck valves or operate utility equipment.
